Two Components Solvent Epoxy Primer for non-ferrous floors and surfaces(Kit)

Modo de empleo :

To use it, the two components must be mixed in a proportion of 3:1 by weight (2.67:1 by volume), preferably mechanically, failing which perfect homogenization of the mixture will not be ensured. To achieve this proportion, the total content of component B must be poured onto component A. It is necessary to respect the useful time of use of the mixture (6 hours), since after this period the paint is unusable, appreciating a significant increase in the viscosity. The paint is prepared ready to use. If the complete containers are not used and in order to obtain optimal results, the quantities indicated above will be weighed. It is not advisable to divide products to make partial mixtures, since an inadequate mixing ratio can affect the final properties of the product. Surface preparation: New floor: On concrete floors, at least 28 days should be allowed to pass so that the floor is perfectly set. Once set, the milk of lime generated by the concrete setting process must be removed, since it closes the pore and causes loss of adhesion. Therefore, once the floor has set, a surface roughening must be carried out using a milling or shot blasting machine so that the product penetrates the surface better. If mechanical means are not available, it is recommended to treat with 5% hydrochloric acid for 15 minutes and then rinse with plenty of water until all the acid is removed. Let it dry for 5 days so that the soil is completely dry and free of moisture. The support must be clean of dust, grease and oil. Even mechanical dust extraction is recommended. Once the surface is prepared, the 2C Solvent Epoxy Primer will be applied as an anchor layer in the necessary layers until the recommended thickness is reached and, subsequently, the finish, either 2C Solvent Epoxy Paint or Polyurethane Paint, must be applied over it. 2 C. Painted Floors: It is advisable to remove old paint by shot blasting or mechanical stripping, then proceeding as if it were a new floor. If it is a surface on which the paint is in good condition and smooth, thorough sanding must be carried out in order to eliminate the shine of the old paint and thus ensure that the new paint adheres correctly.

Presentación:

4 & 15 Kg format in two-component kit:

• 4 Kg container: (3 A + 1 B) ; 4.12 L (3 A + 1.12 B)
• 15 Kg container: (11.25 A + 3.75 B) ; 15.46L (11.25A + 4.21 B)

Naturaleza: Epoxy-Polyamide System

Precauciones:

• Apply only when both drying and curing take place at temperatures above 10ºC and below 30ºC. The temperature of the product and the support must also be within this temperature range for said application. The relative humidity must be less than 60%, and that of the support less than 12%.
• Do not expose containers to extreme temperatures
• Do not apply if rain or strong winds are expected.
• If not using complete containers, respect the mixing proportion of both components: 3 parts of A: 1 part of B (by weight)
• Avoid using different batches in the same cloth or, failing that, mix the current jar with the previous one at 50% to reduce the normal differences between batches.

Safety:

• Before using the product you must carefully read the instructions on the packaging. For more information see Safety Data Sheet.
• Remember that the mixture has a maximum use time of 6 hours, since high temperatures can reduce it, even causing a reaction with gas release and high temperature.

Almacenamiento: The product must be stored in its original packaging in areas protected from the sun and at temperatures below 30ºC.

Memoria Descriptiva: Adherence Test: UNE-EN ISO 2409:2013 Standard. Paints and varnishes. Lattice cutting test. - Concrete: 5 - Tiles: 5 - Polyester: 5 - Glass: 5 - Steel: 5 - Aluminum: 5 Hardness Test: UNE-EN ISO 1522:2006 Standard. Paints and varnishes. Pendulum damping test. Final hardness 7 days >350s

Color producto: Colorless

Aspecto: Liquid

Aspecto aplicado: Glossy

Tipo: al_agua

Diluyente: Jafep Epoxy Solvent

Secado: 4 - 6 hours

Rendimiento: 11-12 m²/L or 12-13 m²/Kg for 40 dry microns

Tinción: 11-12 m²/L or 12-13 m²/Kg for 40 dry microns

Repintado: 24 hours

Espesor mínimo: 120 microns dry in two coats

Curado: 7 days

Permeabilidad al agua líquida: 7 days

Herramienta: Brush, Roller, Airless, Spray Gun